COLO.Science · Technical Specification
PRO6240
Fluoride Ion Selective Electrode · F- ISE · BNC(Q9) Connector
PRO6240 Fluoride Ion Selective Electrode is an ion-selective electrode for fluoride ion measurement in compatible ISE-capable meters.
The electrode uses a crystalline-state membrane, plastic body and BNC(Q9) connector, and is intended for economical ion measurement workflows such as direct reading,
standard addition, sample addition and GRAN methods when supported by the connected meter.
Fluoride ISE
F- species
10-1 to 10-6 M
Crystalline membrane
Plastic body
Ø12 × 120 mm
5–45°C
BNC(Q9)
Reference electrode required
PRO6240 · fluoride ion selective electrode · main unit
Model / SKU
PRO6240
Fluoride ISE
Fluoride ISE
Address / HQ
Polje ob Sotli 4
SI-3255, Slovenia
SI-3255, Slovenia
Contact
sales@colo.si
+386 64 222 724
+386 64 222 724
Page 1 / 5
PRO6240 · Fluoride Ion Selective Electrode
Technical data sheet · Informational document · Controlled electronic document
Contact: Request configuration confirmation
Contact: Request configuration confirmation
PRO6240 · technical specification
Fluoride ion selective electrode for compatible ISE-capable meters
F- fluoride
10-1 M ~ 10-6 M
Crystalline-state membrane
BNC(Q9)
Reference electrode required
— Electrode configuration must match the meter and reference electrode system
📋 Product Overview
Application profile
Fluoride ion measurement: designed for fluoride ion activity / concentration measurement using a compatible ion meter or ISE-capable electrochemistry meter.
Routine ISE workflows: suitable for economical ion measurement where direct reading or addition-based methods are required.
Laboratory and QA/QC use: applicable in water, environmental, educational and routine analytical workflows where fluoride ion determination is required.
Method-dependent operation: available ISE modes such as Auto-reading, Standard Add, Sample Add and GRAN depend on the connected meter functions.
System concept
Ion-selective electrode: PRO6240 is the measuring electrode for fluoride ions.
Reference electrode: ISE measurement requires cooperation with a compatible reference electrode, for example 232-01-X reference electrode or equivalent confirmed configuration.
Connector compatibility: connector selection must match the meter input. PRO6240 is specified with BNC(Q9) connection; S7 versions require an S7-BNC(Q9) cable when applicable.
Single SKU principle: connector visual references in this document do not define a separate product SKU; the electrode SKU remains PRO6240.
Key features
Species: fluoride ion, F-.
Measuring range: 10-1 M to 10-6 M.
Membrane: crystalline-state membrane for fluoride ion-selective measurement.
Body: plastic electrode body for routine laboratory handling.
Dimensions: Ø12 × 120 mm electrode format.
Working temperature: 5–45°C operating range.
Connector: BNC(Q9), meter compatibility to be confirmed before delivery.
Core technical summary
| Parameter | Specification |
|---|---|
| Model / SKU | PRO6240 |
| Species | Fluoride (F-) |
| Name | Ion selective electrode |
| Measuring range | 10-1 M ~ 10-6 M |
| Membrane | Crystalline-state membrane |
| Body | Plastic |
| Dimension | Ø12 × 120 mm |
| Working temperature | 5–45°C |
| Connector | BNC(Q9) |
Ion speciesFluoride F-
Range10-1–10-6 M
MembraneCrystalline-state
ConnectorBNC(Q9)
Page 2 / 5
📊 Technical Specifications
Electrode specification
| Parameter | Specification |
|---|---|
| Model / SKU | PRO6240 |
| Species | Fluoride (F-) |
| Product name | Ion selective electrode |
| Electrode type | Fluoride ion selective electrode |
| Measuring range | 10-1 M ~ 10-6 M |
| Membrane | Crystalline-state membrane |
| Body material | Plastic |
| Dimension | Ø12 × 120 mm |
| Working temperature | 5–45°C |
| Connector | BNC(Q9) |
ISE measurement mode support
| Measurement mode | Technical note |
|---|---|
| Auto-reading | Available when supported by the connected ISE-capable meter. |
| Standard Add | Addition-based ISE method; availability depends on meter software/function set. |
| Sample Add | Sample addition method; availability depends on meter software/function set. |
| GRAN methods | Supported only where the connected meter includes GRAN calculation functions. |
Compatibility and configuration
| Item | Configuration note |
|---|---|
| Meter compatibility | Use only with a compatible ion meter or ISE-capable electrochemistry meter. |
| Reference electrode | ISE probe requires a compatible reference electrode; example: 232-01-X reference electrode. |
| Connector requirement | Connector must match the meter input. This configuration is specified as BNC(Q9). |
| S7 option note | Where an S7 electrode configuration is used, an S7-BNC(Q9) cable is required to connect to a BNC(Q9) meter input. |
| Connector image note | Connector detail image is for visual reference only; it does not assign a second SKU to the electrode. |
| Single SKU rule | All product identification in this technical sheet remains PRO6240. |
| Final configuration | Confirm electrode, cable/reference electrode and meter compatibility in the official quotation. |
Specification note
Sample matrix: confirm sample type, expected fluoride concentration range and any matrix preparation requirements before final configuration.
Reference system: final measurement reliability depends on correct pairing of ISE, reference electrode, meter and method settings.
Connector: BNC(Q9) compatibility should be checked against the selected meter input before delivery.
Documentation: final method, accessories and calibration/standard solutions should be confirmed for each quotation.
Technical values are provided for product selection and orientation. Final delivered configuration, reference electrode, connector/cable arrangement, accessory set and documentation should be confirmed through the official COLO.Science quotation or manufacturer-confirmed offer.
Page 3 / 5
🧰 Visual Support, Compatibility and Use Notes
Typical configuration logic
Main product: PRO6240 Fluoride Ion Selective Electrode.
Measurement species: fluoride ion F-.
Reference electrode: compatible reference electrode required for ISE measurement, such as 232-01-X or confirmed equivalent.
Meter connection: BNC(Q9) connector must match the meter input.
Cable note: if an S7 electrode/cable arrangement is used, confirm S7-BNC(Q9) cable compatibility with the meter.
Image references
SKU note — connector image is not a second product code
The electrode is identified in this document as PRO6240. The connector image is included only to help visually explain the BNC(Q9) connection type. Final connector/cable/reference-electrode compatibility should always be checked against the selected meter and confirmed before delivery.
📌 Selection and Use Notes
For fluoride ISE measurement
Range: check that expected sample concentration fits the 10-1 to 10-6 M measurement range.
Method: confirm whether direct reading, Standard Add, Sample Add or GRAN method is required.
For meter compatibility
Connector: confirm BNC(Q9) input or required adapter/cable before order confirmation.
Software: addition and GRAN methods require suitable meter functions.
For quotation
Include: meter model, desired measuring range, sample type and method requirement.
Confirm: electrode, reference electrode, cable and standards/accessories as one functional measurement set.
Page 4 / 5
COLO.Science · Final Support Page
Manufacturer and support
COLO Lab Experts
Polje ob Sotli 4, SI-3255, Slovenia
Selection guidance: Send the meter model, sample type, expected fluoride range, required ISE method and connector/reference-electrode requirements.
COLO.Science can help confirm the correct PRO6240 electrode configuration and compatible accessory set for your measurement workflow.
Quick contact
COLO.Science · PRO6240 fluoride ion selective electrode support
Need help confirming the correct fluoride ISE configuration?
Send the meter model, sample matrix, expected fluoride concentration range, required method and connector/reference-electrode requirements. COLO.Science can help confirm whether PRO6240 is the correct fluoride ISE configuration for your laboratory workflow.
Official configuration and manufacturer-confirmed specification notice:
This technical specification is provided for orientation, product selection and general information only. It does not represent the final binding technical specification, delivered configuration, accessory set, procurement requirement or acceptance criterion for a specific unit. The final official technical specification is only the specification confirmed by the manufacturer and issued for the exact configuration through an official COLO.Science quotation, proforma invoice, contract document, order confirmation or manufacturer-approved technical offer. Any values, options, accessories, connector arrangements or configurations shown in this document must be verified for the specific delivery and should not be used as an exclusion or elimination criterion in procurement procedures without written manufacturer confirmation.
This technical specification is provided for orientation, product selection and general information only. It does not represent the final binding technical specification, delivered configuration, accessory set, procurement requirement or acceptance criterion for a specific unit. The final official technical specification is only the specification confirmed by the manufacturer and issued for the exact configuration through an official COLO.Science quotation, proforma invoice, contract document, order confirmation or manufacturer-approved technical offer. Any values, options, accessories, connector arrangements or configurations shown in this document must be verified for the specific delivery and should not be used as an exclusion or elimination criterion in procurement procedures without written manufacturer confirmation.
Page 5 / 5